UAP Firmware 5.60.16

https://www.ui.com/download/un…fi-firmware-56016-u6-lite

https://www.ui.com/download/un…nifi-firmware-56016-u6-lr

https://www.ui.com/download/un…nanohdiw-hdflexhdbeaconhd

Overview

* This release is only for the following models:

UAP-nanoHD/IW-HD/FlexHD/BeaconHD

U6-Lite

U6-LR

Improvements

[UAP-Gen4/5] Improve IPv6 reliability.

[UAP-Gen4/5] Improve DHCP reliability.

[UAP-Gen4/5] Improve overall stability.

[UAP-Gen4/5] Improve 2.4GHz auto-channel selection.

[UAP-Gen4/5] Improve WiFi connectivity.

[UAP-Gen4/5] Improve bluetooth bridge (used to link UniFi Protect Bluetooth devices)

[UAP-Gen5] Improve radar detection.

[U6-LR] Always enable encrypted netconsole logging.

[UAP] Improve 2.4GHz clients stability.

Bugfixes:

[UAP-Gen4/5] Fix intermittent issue of incorrect GTK being used after an interface restart.

[UAP-Gen4/5] Fix 5GHz bandwidth potentially changing erroneously.

[UAP-Gen4/5] Fix adoption failure issue.

[UAP-Gen4/5] Fix PMF connectivity issue

[UAP-Gen4/5] Fix LED issue.

[UAP-Gen4/5] Fix client can't obtain IP address on VLAN SSID issue.

[UAP-Gen4/5] Fix WPA3 SAE connectivity issue.

[UAP-Gen5] Fix standalone mode issue.

[U6-LR] Fix 2.4GHz device periodic disconnection issue.

Additional information:

Instead of using the manual links, you can also subscribe to your desired firmware channel, as described here.

Please refer to this article to find more details on how to identify your Access Point generation.

Your device built-in display may turn black or unresponsive for ~10 minutes after firmware upgrades to upgrade LCM firmware.

All URLs use HTTPS. This assumes your device(s) are running 3.7.56 or later and that the device's date is properly set. Please change URLs to HTTP for device(s) running earlier firmware or if the date is incorrect (e.g. if device can't reach a NTP server).

War Beta, jetzt Final

So, was neues für die Gen4/5 AP's

UAP Firmware 5.60.18

https://www.ui.com/download/un…nanohdiw-hdflexhdbeaconhd

https://www.ui.com/download/un…nifi-firmware-56018-u6-lr

https://www.ui.com/download/un…fi-firmware-56018-u6-lite

Overview

* This release is only for the following models:

UAP-nanoHD/IW-HD/FlexHD/BeaconHD

U6-Lite

U6-LR

Improvements:

[UAP-Gen4/Gen5] Improve Wireless Uplink connectivity.

[UAP-Gen4/Gen5] Improve 160MHz RSSI reporting for wireless downlinks.

[UAP] Improve memory usage.

Bugfixes:

[UAP-Gen4/Gen5] Fix intermittent WiFi connectivity issue with power-saving clients.

[UAP] Fix intermittent firmware update failure on wirelessly connected APs adopted to a UDM.

[HW] Avoid intermittent failed readoption loops.

Additional information:

Instead of using the manual links, you can also subscribe to your desired firmware channel, as described here.

Please refer to this article to find more details on how to identify your Access Point generation.

Your device built-in display may turn black or unresponsive for ~10 minutes after firmware upgrades to upgrade LCM firmware.

All URLs use HTTPS. This assumes your device(s) are running 3.7.56 or later and that the device's date is properly set. Please change URLs to HTTP for device(s) running earlier firmware or if the date is incorrect (e.g. if device can't reach a NTP server).

Schalte einmal zu Test Zwecken das 5GHz WLAN ab.

Viele iot Funken nur in 2,4, sobald ein 5er Netz mit selber SSID da ist kommen sie durcheinander

Die iot Auto Optimierung mal testweise raus.

Mit Auto Optimierung habe ich bei Unifi keine gute Erfahrungen.

Kannst du einmal machen, ansonst würde ich den Sauger auf Werkseinstellungen bringen und ganz neu mit dem WLAN verbinden.

UAP Firmware 5.60.19

https://www.ui.com/download/un…nanohdiw-hdflexhdbeaconhd

https://www.ui.com/download/un…nifi-firmware-56019-u6-lr

https://www.ui.com/download/un…fi-firmware-56019-u6-lite

Overview

* This release is only for the following models:

UAP-nanoHD/IW-HD/FlexHD/BeaconHD

U6-Lite

U6-LR

Bugfixes:

[UAP-Gen4/Gen5] Fix wireless uplink priority selection not working in some cases.

[UAP-Gen4/Gen5] Fix wireless adoption of APs, USP-Plug/Strip, and UniFi Protect cameras.

[UAP-Gen4/Gen5] Fix not being able to change the transmission power when Uplink Connectivity Monitor is enabled

Additional information;

U6-Pro/Mesh needs to be upgraded to 5.67.0 first before upgrading to 5.68.0+.

Instead of using the manual links, you can also subscribe to your desired firmware channel, as described here.

Please refer to this article to find more details on how to identify your Access Point generation.

Your device built-in display may turn black or unresponsive for ~10 minutes after firmware upgrades to upgrade LCM firmware.

All URLs use HTTPS. This assumes your device(s) are running 3.7.56 or later and that the device's date is properly set. Please change URLs to HTTP for device(s) running earlier firmware or if the date is incorrect (e.g. if device can't reach a NTP server).

UAP Firmware 5.60.23

https://www.ui.com/download/un…nanohdiw-hdflexhdbeaconhd

https://www.ui.com/download/un…nifi-firmware-56023-u6-lr

https://www.ui.com/download/un…fi-firmware-56023-u6-lite

Overview

* This release is only for the following model(s):

• UAP-nanoHD/IW-HD/FlexHD/BeaconHD
• U6-Lite
• U6-LR

Improvements

• [UAP-Gen4/Gen5] Improve connectivity with IOT WiFi clients.
• [UAP-Gen5] Improve WiFi firmware stability.

Bugfixes

• [UAP-Gen5/Gen4] Fix incorrect reporting of bandwidth in RF Scan.
• [UAP] Fix memory leak in WiFi authenticator.

Additional information

• Instead of using the manual links, you can also subscribe to your desired firmware channel, as described here.
• Please refer to this article to find more details on how to identify your Access Point generation.
• Your device built-in display may turn black or unresponsive for ~10 minutes after firmware upgrades to upgrade LCM firmware.
• All URLs use HTTPS. This assumes your device(s) are running 3.7.56 or later and that the device's date is properly set. Please change URLs to HTTP for device(s) running earlier firmware or if the date is incorrect (e.g. if device can't reach a NTP server).