Final UniFi Protect Device All

Es gibt 22 Antworten in diesem Thema, welches 5.073 mal aufgerufen wurde. Der letzte Beitrag () ist von BlackSpy.

    UniFi Protect Cameras 4.66.11

    https://community.ui.com/releases/UniFi-Protect-Cameras-4-66-11/237f1c30-7e48-4157-8aef-f7d1751bd6f8


    Overview

    UniFi Protect Cameras 4.66.11 reduces the talkback latency for cameras with two-way audio and improves the accuracy of Smart Detections.

    Improvements

    • Added an auto-recovery feature if a camera is stuck during the firmware upgrade process.
    • Improved the accuracy of Person, Vehicle, and Smoke Alarm detections.
    • [AI-Theta] Updated the design for the built-in display.
    • [AI-Pro] Improved audio & image quality.
    • [AI-360] Improved de-warping UX in live view.
    • [G4-Doorbell Pro] Added support for dog animation on G4 Doorbell Pro and G4 Doorbell Pro PoE.
    • [G4-PTZ] Improved the PTZ operation UX and style of Keyboard Control.
    • [G5-Pro] Improved the G5-Pro-Enhancer switching performance.
    • [G5 Pro] Changed the Default name to "G5 Pro + Enhancer" with enhancer.
    • [G5-Bullet/G5-Dome/G5-Flex/G5-Pro] Improved device stability.
    • [G3-Instant/G4-Instant/G5-Series] reduced talkback latency on the camera speaker side.
    • [Wireless Camera] Improved the AP selection logic after the camera reboot.
    • [Wireless Camera] Improved wireless connectivity under poor WiFi conditions.
    • [Wireless Camera] Improved the resiliency of the BLE adoption process.

    Bugfixes

    • Fixed an issue where the camera would be offline for several minutes when a new VLAN setting was applied.
    • Fixed timestamps could be identified as License Plates.
    • Fixed Crossing Lines's inability to detect multiple objects (Person/Vehicle) in one event.
    • [G3-Instant/G4-Instant] Fixed an issue where the device could get stuck in booting up.
    • [G4-PTZ] Fixed Auto Tracking might get stuck randomly.
    • [G4-Doorbell] Fixed an issue where the Recording Quality section gets disabled if High Frame Rate mode is enabled.
    • [G4-Pro] Fixed an issue where the camera couldn't focus properly.
    • [G4-PTZ] Fixed the issue that the highlight is not shown upon editing the motion zone.
    • [G4-Doorbell-Pro] Fixed the black ring artifacts appearing at the bottom of the video.
    • [G5-Bullet|G5-Dome|G5-Flex] Fixed the issue regarding the purple/pink line appearing on the edge of the screen.
    • [G5-Pro] Fixed abnormal image issue when the user toggles Auto Rotate in the image orientation settings.
    • [AI-360] Fixed the issue regarding the speaker being muted during 2-way audio.
    • [AI-Pro] Fixed the issue that the camera can not achieve 30 fps in non-HDR mode.
    • [AI-Theta] Fixed the issue about the user’s voice getting echoed while using Talkback.
    • [AI-DSLR] Fixed an overexposure issue.

    UniFi Protect Floodlight 1.11.2

    https://community.ui.com/releases/UniFi-Protect-Floodlight-1-11-2/9804d938-1536-4e2a-bc6d-9d4e4d982e69


    Overview

    UniFi Protect Floodlight 1.11.2 includes the below improvement.

    Improvements

    • Improved device stability.

    UniFi Protect Viewport 1.3.118

    https://community.ui.com/releases/UniFi-Protect-Viewport-1-3-118/500c8a8c-ac43-4491-b29b-4ba354485e06


    Overview

    UniFi Protect Viewport 1.3.118 introduces support for 16 cameras in Live View and includes performance and stability enhancements.

    Improvements

    • Added support for new live view grid layouts (up to 16 cameras).
    • Added support for displaying the Protect update status when the Console/Protect/Viewport is updating.
    • Updated UI logo.
    • Changed the default video quality configuration for various grid sizes.
    • Improved the latency of the video streams.

    Bugfixes

    • Fixed an issue where the Viewport would restart if cameras were being power cycled repeatedly.
    • Fixed a rare crash when repeatedly changing settings for Live View/Grid Size.
    • Fixed an issue where changing Motion or Time did not reflect on the Viewport.

    UniFi Protect Chime PoE 1.4.5

    https://community.ui.com/releases/UniFi-Protect-Chime-PoE-1-4-5/bbcf1dea-908b-4034-82fc-a6c530c7411f


    Overview

    UniFi Protect Chime 1.4.5 includes the improvement and fixes listed below.

    Improvements

    • Improved device stability.

    Bugfixes

    • Fixed incorrect LED behavior during device update.

    Additional information

    • This release is only for the PoE Chime model.

    UniFi Protect Chime 1.4.6

    https://community.ui.com/relea…3d-411b-b3bf-1c88d7cc6a39


    Overview

    UniFi Protect Chime 1.4.6 includes the improvement and fixes listed below.

    Improvements

    • Improved WiFi connectivity resiliency.

    Bugfixes

    • Fixed incorrect LED behavior during device update.

    Additional information

    • This release is only for the non-PoE Chime model.
    Zitat von BlackSpy

    UniFi Protect Chime 1.4.6

    https://community.ui.com/relea…3d-411b-b3bf-1c88d7cc6a39


    Overview

    UniFi Protect Chime 1.4.6 includes the improvement and fixes listed below.

    Improvements

    • Improved WiFi connectivity resiliency.

    Bugfixes

    • Fixed incorrect LED behavior during device update.

    Additional information

    • This release is only for the non-PoE Chime model.

    Kleine Frage zieht sich die Chime selber das Update?

    Sind zwar separat aufgeführt aber auch in der neusten Final von Protect enthalten und sollten sich automatisch aktualisieren

    Danke 1
    Zitat von fred05

    Doofe frage wo sehe ich den Firmware stand bei der Glocke?

    Unter Protect -> Unifi Devices -> Chime -> Overview



    Des Weiteren kannst du die Chime einem bestimmten AP zuweisen


    Unter Network -> UniFi Devices -> Chime -> Settings


    Gefällt mir 1

    Ja die Chime springt nicht zwischen den APs hin und her sondern von heute auf morgen war an der Stelle wo die Chime war einfach verbindungssbrüche daher habe ich die woanders geparkt jetzt.

    Es hat sich aber nichts im Netzwerk geändert.


    Das mit dem Fixen vom AP ist doof wenn der AP weg ist hatte ich schon bei einem anderen Produkt lies sich das Gerät nicht nenne es mal ausbilden und auf anderen AP Fixieren.

    Updates der Chime sowie von den Cam's werden automatisch ausgerollt, wenn Protect aktualisiert wird.


    Welche Protect Version hast du am laufen?

    Seltsam die neuste ist die 2.9.33 als Final und im Beta die 2.9.41.

    Mal in die Übersicht des Gateway geschaut?

    Welche FW hast du auf der SE? um Protect 2.9.x zu installieren benötigst du mindestens eine FW 3.0 oder höher auf der SE

    Ganz seltsam, Stelle mal deine Updates von offiziell auf Beta, geh in die Network App unter Settings/Update und klicke "Search Update". Danach wieder in die SE Settings und Update wieder von Beta auf offiziell stellen.