UniFi Network Application 8.0.24

https://community.ui.com/releases/UniFi-Network-Application-8-0-24/43b24781-aea8-48dc-85b2-3fca42f758c9

Overview

UniFi Network Application 8.0.24 adds support for Admin Settings Change Logs, increases the network limit to 255, and includes several stability fixes and improvements.

Admin Settings Change Logs

Allows you to track all settings changes and who performed the changes.

Improvements

• Added Admin Settings change System Logs.
• Increased default network limit to 255. Some devices have lower limits such as USG, or InWall AP models.
• Splitted the Clients list into Online/Offline tabs.
• Added payment name to the Guest Portal landing page.
• Added 24HR TX Retries to Sites Overview.
• Added device model column to Radio Manager.
• Added pagination to Radio Manager.
• Added support for Korean and Spanish language.
• Added WAN/LAN IP addresses to the Dashboard for Network Application Servers.
• Added validation when a new network is trying to use a subnet that is already used by an OpenVPN Client.
• Added support for PPPoE WAN without credentials. This requires UniFi OS 3.2 or newer.
• Allow removing networks with references. You will receive a warning message before deletion.
• Improved Guest Portal loading latency.
• Increased the index space for Firewall rules.
• Updated the list of Dynamic DNS providers.

Bugfixes

• Fixed an issue with configuring radios of UAP-XG's and UAP-BaseStationXG's via Radio Manager.
• Fixed an issue where IPv6 Prefix Delegation or IPv6 Single Network was broken on non-Default networks. This only affects the UXG line of devices.
• Fixed inability to edit Port/Device settings when an incorrect channel was applied on an AP.
• Fixed inability to open Internet Settings in rare cases.
• Fixed an issue where the All Traffic row in Traffic Monitor didn't include unidentified traffic.
• Fixed an issue where some port profiles failed to get applied on InWall APs.
• Fixed a rare case where Traffic Rules would stop working while Ad Blocking was enabled.
• Fixed an issue where the Network Application wasn't getting stopped on Windows during upgrades or removal.
• Fixed incorrectly reported built-in antenna gain.
• Fixed the inability to connect to Guest Portals in rare cases.
• Fixed the inability to open Security settings in rare cases.
• Fixed rare gateway configuration error due to invalid default RADIUS profile ports.
• Fixed rare gateway configuration error on UDM/UDR/UDW.
• Fixed rare gateway configuration errors.
• Fixed an issue where Suspicious Activity was allowed to be applied on non-local networks.
• Fixed an issue where client uptime could be invalid, the fix applies to new connections.
• Fixed an issue where Device type filters were resetting selected columns.
• Fixed an issue where Client Isolation couldn't be disabled when using a Guest Portal.
• Fixed an issue where port anomalies were not showing details on Port diagrams.

Additional information

• Create a backup before upgrading your UniFi Network Application in the event any issues are encountered.
• See the UniFi Network Server Help Center article for more information on self-hosting a server.
• UniFi Network Application 7.5 and newer requires MongoDB 3.6 (up to 4.4) and Java 17.

UniFi Network Native Application for UniFi OS

A specific application version that is only compatible with the UDM and UDR (running UniFi OS 3.1.6 or newer).

• The UniFi OS update uses the application version that is required for your console.
• The manual update process via SSH requires you to use the compatible package. Incompatible packages will be rejected on installation.
• Older UniFi OS versions (before UniFi OS 3.1.6) on the UDM and UDR still use regular UniFi Network Application for UniFi OS.

Download links

UniFi Network Application for Windows

UniFi Network Application for macOS

UniFi Network Application for Debian/Ubuntu

UniFi Network Application for UniFi OS

UniFi Network Native Application for UniFi OS

UniFi Network Application for unsupported Unix/Linux distros *** DIY / Completely unsupported ***

unifi_sh_api (shell library)

UniFi Network Application 8.0.26

https://community.ui.com/releases/UniFi-Network-Application-8-0-26/3f2444ce-92dd-4aef-bfff-3f0d447c9783

Bugfixes

• Fixed an issue where WAN2 configurations were removed after a firmware upgrade when using 8.0.24 with a Static or PPPoE WAN configuration.
• This only prevents new occurrences. Affected setups need to be restored from a backup before this issue or re-create their WAN config.
• Fixed gateway/console showing offline when WAN interface cannot be found.

Additional information

(Recommended) - Create an up-to-date backup before upgrading your UniFi Network Application settings in the event any issues are encountered.

• Existing UniFi Network Applications must be on one of the following versions to upgrade directly to this version:

8.0.26 and earlier 8.0.x versions.
7.5.187 and earlier 7.5.x versions.
7.4.162 and earlier 7.4.x versions.
7.3.84 and earlier 7.3.x versions.
7.2.97 and earlier 7.2.x versions.
7.1.68 and earlier 7.1.x versions.
7.0.26 and earlier 7.0.x versions.
6.5.55 and earlier 6.5.x versions.
6.4.54 and earlier 6.4.x versions.
6.3.51 and earlier 6.3.x versions.
6.2.26 and earlier 6.2.x versions.
6.1.71 and earlier 6.1.x versions.
6.0.45 and earlier 6.0.x versions.
5.14.25 and earlier 5.14.x versions.
5.13.33 and earlier 5.13.x versions.
5.12.72 and earlier 5.12.x versions.
5.11.52 and earlier 5.11.x versions.
5.10.27 and earlier 5.10.x versions.
5.9.33 and earlier 5.9.x versions.
5.8.30 and earlier 5.8.x versions.
5.7.28 and earlier 5.7.x versions.
5.6.42 and earlier 5.6.x versions.
Most earlier versions are also supported for a direct upgrade, going back to 3.1.0.

UniFi Network Application updates may cause your adopted devices to be re-provisioned.The UC-CK is not supported as of Network application version 7.3 and newer.UniFi Network Application 7.5 or newer requires MongoDB 3.6 (up to 4.4) and Java 17.

Native Application for UniFi OS specific This is only compatible with the UDM/UDR that run UniFi OS 3.1.6 or newer, don't attempt to install it on any other consoles. Older UniFi OS versions on the UDM/UDR use the regular UniFi OS Network application.

Microsoft Windows specific (when running it as a service) Users running 64-bit Windows should only have 64-bit Java installed. If you have 32-bit Java installed then we recommend uninstalling it.

Debian/Ubuntu/Linux specific For Debian/Ubuntu users installing via our repo, please update your APT source (see HERE).We support MongoDB 3.6 since 5.13.10, older UniFi Network Application versions only support up to MongoDB 3.4.The UniFi Network application requires Java 17 to be installed on the system that runs the application. Java 18 and later are not supported.

Download links

UniFi Network Application for Windows

UniFi Network Application for macOS

UniFi Network Application for Debian/Ubuntu

UniFi Network Application for UniFi OS

UniFi Network Native Application for UniFi OS

UniFi Network Application for unsupported Unix/Linux distros *** DIY / Completely unsupported ***

unifi_sh_api (shell library)

UniFi Network Application 8.0.28

https://community.ui.com/releases/UniFi-Network-Application-8-0-28/f7492865-778d-4539-aaf8-3fb09c4279b0

Overview

UniFi Network Application 8.0.28 includes the bugfixes listed below.

Bugfixes

• Fixed the inability to upload hotspot landing page images on consoles running the Native Application (UDR, UDM, Express).
• Fixed the inability to see the DNS Shield setting in rare cases.
• Fixed the inability to open Security Logs in rare cases.
• Fixed the inability to select multiple APs in Display Options on the Clients page.
• Fixed the inability to update Virtual Networks from the Topology page when DHCP Guarding or DHCP Options are enabled.
• Fixed the inability to see devices that are Pending Adoption as Site Administrator on Network Application Servers.
• Fixed an issue where mesh links went down due to an invalid Monitor IP Address for Wireless Meshing after updating to Network Application 7.5 or newer and Access Point firmware version 6.6.12 or newer.
• Fixed gateway configuration/provisioning issues when the WAN interface can't be found.

Additional information

• Create a backup before upgrading your UniFi Network Application in the event any issues are encountered.
• See the UniFi Network Server Help Center article for more information on self-hosting a server.
• UniFi Network Application 7.5 and newer requires MongoDB 3.6 (up to 4.4) and Java 17.
• UniFi Network Application updates may cause your adopted devices to be re-provisioned.

UniFi Network Native Application for UniFi OS

A specific application version that is only compatible with the UDM, UDR and Express (running UniFi OS 3.1.6 or newer).

• The UniFi OS update uses the application version that is required for your console.
• The manual update process via SSH requires you to use the compatible package. Incompatible packages will be rejected on installation.
• Older UniFi OS versions (before UniFi OS 3.1.6) on the UDM and UDR still use regular UniFi Network Application for UniFi OS.

Download links

UniFi Network Application for Windows

UniFi Network Application for macOS

UniFi Network Application for Debian/Ubuntu

UniFi Network Application for UniFi OS

UniFi Network Native Application for UniFi OS

UniFi Network Application for unsupported Unix/Linux distros *** DIY / Completely unsupported ***

unifi_sh_api (shell library)

UniFi Network Application 8.1.113

https://community.ui.com/releases/UniFi-Network-Application-8-1-113/af46fd38-8afe-4cef-8de1-89636b02b52c

Overview

UniFi Network Application 8.1.113 adds support for Network Viewer, NAT Pooling, L3 Network Isolation (ACL), Device Isolation (ACL), OSPF Dynamic Routing, and improves the Topology experience by allowing to rotate it.

Network Viewer

Detailed overview of the entire network allowing you to see everything in one place.

• See WiFi, Virtual Networks, Internet, VPNs and much more.
• Directly open the relevant settings page to quickly alter the configuration.

NAT Pool

Adds the ability to NAT traffic to a pool of addresses on specific networks.

• Configure NAT Pool using the Internet Source / NAT option on Virtual Networks.
• This option will appear when Additional IP Addresses are configured on the WAN.

Addition of custom Source and Destination NAT rules is scheduled for an upcoming release.

L3 Network Isolation and Device Isolation (ACL)

Control traffic on your network using Access-Lists (ACLs) on UniFi Switches.

• L3 Network Isolation automatically blocks all traffic between devices in different networks.
• Device Isolation automatically blocks all traffic between devices in the same network.
• See the Device and Network Isolation Help Center article for more information.

Addition of custom Access Lists is scheduled for an upcoming release.

Topology Rotation

Rotate your topology horizontally for a better overview on wide screen displays.

OSPF Dynamic Routing Protocol

Enable OSPF on Virtual Networks to form neighbor connections with other gateways and exchange routes.

• Enable OSPF on one or more Virtual Networks.
• Customize OSPF area types, timers, cost, passive interfaces and authentication settings.
• Control advertisement of connected and static (Route-Based IPsec VPN) routes with redistribution.
• Forming OSPF neighbor connections over Route-Based IPsec VPNs is scheduled for an upcoming release.
• See the OSPF Help Center article for more information.

Addition of the BGP Dynamic Routing Protocol is scheduled for an upcoming release.

InnerSpace

A powerful deployment visualization tool that allows you to view your UniFi system's WiFi coverage in your own floor plan.

Improvements

• Added tabs to the side panel to navigate quickly through recently visited panels.
• Enabled with Side Panel Tabs option in the Advanced System settings (disabled by default).
• Added the ability to toggle "Allow Internet Access" and "Isolate Network" via the Network settings.
• This previously only existed in VLAN Magic settings.
• Isolate Network blocks communication to all other Virtual Networks.
• Added NAT Pooling. Requires a UniFi (Cloud) Gateway with firmware version 3.2.9 or newer.
• Added support for OSPF. Requires a UniFi (Cloud) Gateway with firmware version 3.2.12 or newer.
• OSPF is limited to one instance and cannot be used with Site Magic simultaneously.
• Added InnerSpace for Network Application Servers.
• Added L3 Network Isolation and Device Isolation (ACL). Requires a UniFi Switch with firmware 7.0.44 or newer.
• Added option to invert the Traffic Statistics to view by client device or application data.
• Added the ability to copy Switch configuration between models with the same port counts.
• Added updating progress bar in the Devices list.
• Added STP and Loop detection logs. They will show in Network Viewer page in Network AI section.
• Added the option “All” to the AP group setting in WiFi settings.
• Renamed Isolation in Network settings to Guest Network.
• Renamed Traffic Routes to Policy-Based Routes.
• Added Fallback option to Policy-Based Routes.
• Added support for RF Scanning 6GHz channels.
• Added warning messages when adding many Multicast DNS networks.
• Added Etherlighting Breathing on/off toggle.
• Added 1h time range to Traffic Statistics.
• Allow removing admins without any roles on Network Application Servers.
• Allow using .local domains in Virtual Network and Client settings.
• A warning is shown instead of completely preventing the use of it.
• Improved validation for RADIUS authentication credentials.
• Improved feedback for devices in the Adoption Failed state.
• Improved client roaming System Logs.
• Improved Traffic Stats data collection to improve data accuracy.
• Upgrading to this version will take longer for larger setups due to stat migration.
• Improved validation for Port Forward ports.
• Improved validation message for VLAN0 QoS Tag.
• Improved Admins page UX on Network Application Servers.
• Improved Connection Logs timeline user experience.
• Related Content Filtering settings are now also getting removed when removing Networks.
• Improved stability on Express Consoles.
• Improved user experience when Networks are removed/added/modified.
• Improved admin changelogs.
• Improved DHCP Leased IP user experience and accuracy.
• Improved Network isolation user experience.
• Improved Topology page user experience.
• Updated the WiFi Coverage user experience.
• Updated the Settings layout user experience.
• Added RADIUS Secret validation restriction for backslashes.
• Moved the AP selector to the top bar on the all Radio section.
• Reduced latency test from 60 to 30 seconds.
• Removed VLAN range validation in the Internet Settings.
• Automatically disable Fixed IP for devices/clients when their IPs are excluded by subnet changes.

Firewall

• Improved Firewall Rules user experience.
• Firewall Rules are now more detailed showing additional columns.
• Combined Traffic and Firewall Rules into one section with Simple and Advanced toggle.
• Advanced section also includes Traffic Rules to show the relationship between Traffic and Firewall Rules.
• Added Firewall Rule IDs.
• Added filters to Firewall Rules.
• Improved Firewall Rule creation.
• Added validation for how many IP addresses can be added for Traffic Rules.
• Updated Traffic Rules user experience.

IPv6

• Added IPv6 WAN address to Internet Settings and Internet Health.
• Added IPv6 address and subnet to the Network settings for Prefix Delegation, Single Network and Static.
• Added IPv6 link local address to the Network settings.
• Added last seen IPv6 address for Offline clients.
• Added IPv6 address to Wireless clients panel. Requires UniFi Access Point firmware version 7.0 or newer.
• Prevent disabling IPv6 when DS-Lite is enabled.

VPN

• Added more information to the VPN Client settings.
• Added validation for Local and Remote IP Uniqueness for Site-to-Site VPNs.
• Added ability to configure Cipher for OpenVPN Site-to-Site VPNs. Requires a UniFi (Cloud) Gateway with firmware version 3.2.12 or newer.
• Allow bigger network size for VPN Servers on UniFi (Cloud) Gateways.
• Improved WireGuard VPN Server Client IP Validation.

WiFi

• Added a note with WiFi 6 deployment instructions in the WiFi settings when a 6GHz capable AP is adopted.
• Updated WiFi Network creation user experience when setup contains a 6GHz capable AP.
• The 6GHz band is automatically selected and defaults to WPA2/WPA3 encryption.
• Removed band steering in the AP property panel for Gen7 APs.

Switching

• Added Isolate Network for L3 Switch networks.
• Improved validation for creating L3 Static Routes.
• Improved user experience when configuring L3 Switch Networks.

Client and Device pages

• Added option to re-order UniFi Devices & Client tables.
• Added TX retry % for clients.
• Added TX retry columns to the Devices page.
• Allow searching clients by 802.1X Identity on the Clients page.

Bugfixes

• Fixed an issue where unidentified traffic wasn't included in the Traffic Statistics page "All Traffic".
• Fixed an issue where Network Isolation was not being applied to some IPv6 Networks.
• Fixed an issue where the OpenVPN client didn't list the server address from the connection.
• Fixed the inability to create WAN2 on consoles with dual WAN after restoring backups from single WAN consoles.
• Fixed the inability to restore backups during the setup wizard on Application Servers in rare cases.
• Fixed page crashes when using the Europe/Kyiv time zone.
• Fixed missing translation for some suspicious activity hits.
• Fixed Admin Change Logs sometimes show IDs instead of change names.
• Fixed sorting issues with the 2.4/5/6 GHz columns on the Device page.
• Fixed inability to create more than 9 pre/post-authorization restrictions in Hotspot Manager.
• Fixed incorrect static IP address shown for PPPoE WAN in Internet Source IP / NAT.

Known issues

• OSPF Default route redistribution is ineffective, this will be fixed in UniFi OS 4.0.

Additional information

• Create a backup before upgrading your UniFi Network Application in the event any issues are encountered.
• See the UniFi Network Server Help Center article for more information on self-hosting a server.
• UniFi Network Application 7.5 and newer requires MongoDB 3.6 and Java 17.
• Version 7.5 till 8.0 supports up to MongoDB 4.4.
• Version 8.1 and newer supports up to MongoDB 7.0.
• UniFi Network Application updates may cause your adopted devices to be re-provisioned.

UniFi Network Native Application for UniFi OS

A specific application version that is only compatible with the UDM, UDR, Express and UCG-Ultra (running UniFi OS 3.1.6 or newer).

• The UniFi OS update uses the application version that is required for your console.
• The manual update process via SSH requires you to use the compatible package. Incompatible packages will be rejected on installation.
• Older UniFi OS versions (before UniFi OS 3.1.6) on the UDM and UDR still use regular UniFi Network Application for UniFi OS.

Download links

UniFi Network Application for Windows

UniFi Network Application for macOS

UniFi Network Application for Debian/Ubuntu

UniFi Network Application for UniFi OS

UniFi Network Native Application for UniFi OS

UniFi Network Application for unsupported Unix/Linux distros *** DIY / Completely unsupported ***

unifi_sh_api (shell library)

UniFi Network Application 8.1.127

https://community.ui.com/releases/UniFi-Network-Application-8-1-127/571d2218-216c-4769-a292-796cff379561

Overview

UniFi Network Application 8.1.127 enhances Firewall Rules visibility and adds tunnel IP addresses and OSPF dynamic routing support for IPsec Site-to-Site VPNs.

Improvements

• Added Tunnel IP to Route-Based IPsec Site-to-Site VPNs.
• Added Dynamic option to Remote Networks for Route-Based IPsec Site-to-Site VPNs.
• Use this option to dynamically learn routes over the VPN via OSPF.
• Added option to disable DHCP Ping Conflict Detection on virtual networks. Requires a UniFi (Cloud) Gateway with version 4.0.1 or newer.
• Pings are sent by default to determine if DHCP leased IP addresses are in use before allocation.
• Optionally disable Ping Conflict Detection if DHCP allocation delays are encountered on large networks.
• For smaller networks, it is recommended to keep Ping Conflict Detection enabled to prevent conflicts.
• Added validation for IPv6 default static routes.
• Improved application startup resiliency.
• Improved user experience when changing WiFi Encryption settings.
• Improved Device image loading.
• Improved the user experience for configuring UBB and UBB-XG devices.
• Improved U-LTE device registration.
• Force auto Prefix Delegation ID for Gateways.
• Prevent additional Network Isolation (ACL) entries if ACL rules limit is reached.
• Prevent selecting L3 Switch networks for OSPF.
• Renamed the Additional Routes option to Remote Client Networks for clients added to WireGuard Servers.
• Improved validation of Remote Client Networks for WireGuard Server clients.
• Prevent WireGuard Server subnet from overlapping with Remote Client Networks.

Firewall

• Improved Firewall Rules user experience by enhancing visibility.
• Predefined Rules now open in side panel.
• Predefined Rules now show additional details such as ports, states, subnets and other criteria that is matched on.
• Updated predefined Firewall Rule names.
• Added descriptions to predefined Firewall Rules in side panel.
• Improved user experience when configuring Traffic Rule directions.

Bugfixes

• Fixed an issue where the Traffic Rules table is not updated after deleting a rule.
• Fixed an issue where the ISP name was not updated after disabling a WAN port.
• Fixed an issue where speed test results were showing undefined speeds in rare cases.
• Fixed Fallback toggle for Policy-Based Routes not working as intended.
• Fixed misplaced description labels on the Topology page when using the Safari browser.
• Fixed the inability to edit Firewall Rules after re-ordering them.
• Fixed an issue where the Voucher Printing option did not open.
• Fixed an issue where Speed Limit data was lost when pausing/resuming Traffic Rules.
• Fixed rare gateway configuration errors.
• Fixed Radar Detections not appearing in System Logs.
• Fixed the inability to adopt USP-Plug/Strip in rare cases.
• Fixed an issue where Stripe Payment in Hotspot Portal failed.
• Fixed missing Up Pkts on the Clients Page.

Additional information

• Create a backup before upgrading your UniFi Network Application in the event any issues are encountered.
• See the UniFi Network Server Help Center article for more information on self-hosting a server.
• UniFi Network Application 7.5 and newer requires MongoDB 3.6 and Java 17.
• Version 7.5 till 8.0 supports up to MongoDB 4.4.
• Version 8.1 and newer supports up to MongoDB 7.0.
• UniFi Network Application updates may cause your adopted devices to be re-provisioned.

UniFi Network Native Application for UniFi OS

A specific application version that is only compatible with the UDM, UDR, Express and UCG-Ultra (running UniFi OS 3.1.6 or newer).

• The UniFi OS update uses the application version that is required for your console.
• The manual update process via SSH requires you to use the compatible package. Incompatible packages will be rejected on installation.
• Older UniFi OS versions (before UniFi OS 3.1.6) on the UDM and UDR still use regular UniFi Network Application for UniFi OS.

Download links

UniFi Network Application for Windows

UniFi Network Application for macOS

UniFi Network Application for Debian/Ubuntu

UniFi Network Application for UniFi OS

UniFi Network Native Application for UniFi OS

UniFi Network Application for unsupported Unix/Linux distros *** DIY / Completely unsupported ***

unifi_sh_api (shell library)