Beta UniFi Access Point 7.x.x derzeit nur Gen 7

Es gibt 23 Antworten in diesem Thema, welches 3.484 mal aufgerufen wurde. Der letzte Beitrag () ist von BlackSpy.

  • UniFi Access Point 7.0.35

    https://community.ui.com/releases/UniFi-Access-Point-7-0-35/6e63b789-11d8-4ea0-b934-2c7024b74321


    Overview

    * This release is only for the U7-Pro.

    Improvements

    • Improved 2.4GHz latency.
    • Improved Voice traffic prioritization.

    Bugfixes

    • Fixed incorrect channel width (20MHz) being reported in device table when 6GHz radio is broadcasting at 320MHz.
    • Fixed connectivity issues with 802.11ac clients (e.g. Broadcom-based MacBooks) leading to stalled WiFi and unexpected disconnects.
    • Fixed missing 6GHz neighbor reports
    • Fixed kernel crashes to improve overall stability.
    • Fixed channel interference being reported as 100% during DFS CAC.
    • Fixed 6GHz channel change causing a full provision (leading to all clients disconnecting) for ~60 seconds.
    • Fixed APs going into "Adoption Failed" state in some cases when using a third-party gateway.

    Additional information

    • Refer to the Help Center article here to determine the UniFi Access Point generation.
    • Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
    • If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

    If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

    • AP model(s)
    • Previous AP release version
    • UniFi Network application version

    Download links

    U7-Pro | md5sum | sha256sum

  • UniFi Access Point 7.0.37

    https://community.ui.com/releases/UniFi-Access-Point-7-0-37/6b400c82-b683-463e-aa3c-2c2ecb8a433e


    Improvements

    • Improved reported client RSSI accuracy.

    Bugfixes

    • Fixed 5GHz radio not broadcasting in Australia on channel 165 at 20MHz channel width until it is rebooted.
    • Fixed newly applied WiFi Speed Limit not taking effect until client reconnects.
    • Fixed uptime for clients being reported incorrectly in some cases.
    • Fixed kernel crashes and stalls to improve stability.
    • Fixed channel width being reset to old configuration if it is configured right as an AP is booting when channel is set to Auto.
    • Fixed client IP address being reported incorrectly sometimes.
    • [Gen7] Fixed incorrect channel width being reported when 240MHz is configured on the 5GHz radio.

    Additional information

    • Refer to the Help Center article here to determine the UniFi Access Point generation.
    • Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
    • If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

    If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

    • AP model(s)
    • Previous AP release version
    • UniFi Network application version

    Download links

    U7-Pro | md5sum | sha256sum

  • UniFi Access Point 7.0.39

    https://community.ui.com/releases/UniFi-Access-Point-7-0-39/1c59eeff-d994-477e-8911-af43744562ce


    Overview

    This release is only available for Gen7 access points.

    Bugfixes

    • [Gen7] Fixed TX Retries being reported incorrectly.
    • [Gen7] Fixed fan turning on during boot on a software-issued reboot.

    Known issues

    • SSIDs using RADIUS assigned VLANs or on different VLANs from the native VLAN may operate at slower than expected speeds. This is our top priority to resolve.

    Additional information

    • Refer to the Help Center article here to determine the UniFi Access Point generation.
    • Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
    • If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

    If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

    • AP model(s)
    • Previous AP release version
    • UniFi Network application version

    Download links

    U7-Pro | md5sum | sha256sum

  • UniFi Access Point 7.0.41

    https://community.ui.com/releases/UniFi-Access-Point-7-0-41/e84c80cd-2003-4780-961f-82fb0516d20d


    Overview

    UniFi Access Point 7.0.41 is only available for the U7-Pro.

    Bugfixes

    • Improved 6GHz roaming performance.
    • Fixed UAPs on large sites (with 1K+ clients) causing excessive CPU utilization on Network Application consoles/servers.

    Known issues

    • SSIDs using RADIUS assigned VLANs or on different VLANs from the native VLAN may operate at slower than expected speeds. This is our top priority to resolve.

    Additional information

    • Refer to the Help Center article here to determine the UniFi Access Point generation.
    • Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
    • If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

    If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

    • AP model(s)
    • Previous AP release version
    • UniFi Network application version

    Download links

    U7-Pro | md5sum | sha256sum

    hoppel118

    Dein Fehler ist immer noch nicht gefixt

  • hoppel118

    Dein Fehler ist immer noch nicht gefixt

    Das scheint sich wohl noch ein Bisschen hinzuziehen.


    Außerdem muss man Ubiquiti anscheinend bei jeder neuen Beta Firmware daran erinnern, den Passus wieder aufzunehmen:


    Known issues

    • SSIDs using RADIUS assigned VLANs or on different VLANs from the native VLAN may operate at slower than expected speeds. This is our top priority to resolve.


    Immerhin ist der Passus schon wieder enthalten. Ich habe zwar dieses VLAN Performance Thema, merke in der täglichen Arbeit im Home Office nichts davon.


    Trotzdem ein wenig unbefriedigend die Situation. Es gibt keine Beta Phase für neue Hardware Produkte mehr. Dann sollten zumindest solche groben Issues bei Produkt Launch beseitigt sein.


    Gruß Hoppel

  • Ich habe auch schon grobe bedenken wen die 7.x auf die anderen AP kommen. Da wird es wieder ein halbes jahr dauern bis diese halbwegs stabil sein wird.

  • UniFi Access Point 7.0.43

    https://community.ui.com/releases/UniFi-Access-Point-7-0-43/27614ece-0c27-42fe-9a83-624c22e9baf8


    Overview

    UniFi Access Point 7.0.43 is only available for the U7-Pro.

    Bugfixes

    • Fixed broken 6GHz client connectivity after changing radio settings (e.g. channel, width, transmit power, etc.). This was introduced in 7.0.41.
    • Fixed minimum (Low) transmit power being used on radios when custom values are configured. This was introduced in 7.0.41.
    • Fixed Medium/Low transmit power configuration resetting to maximum (Auto/High) after firmware update in some cases.
    • Fixed false positive Association failures on the Radios > Connectivity page.
    • Fixed standalone adopted APs sending DNS queries for unifi frequently.
    • Fixed 5GHz SSIDs not broadcasting in Australia when set to channel 165, width 20MHz.

    Known issues

    • SSIDs using RADIUS assigned VLANs or on different VLANs from the native VLAN may operate at slower than expected speeds. This is our top priority to resolve.

    Additional information

    • Refer to the Help Center article here to determine the UniFi Access Point generation.
    • Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
    • If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

    If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

    • AP model(s)
    • Previous AP release version
    • UniFi Network application version

    Download links

    U7-Pro | md5sum | sha256sum


    hoppel118

    Bist leider wieder leer ausgegangen

  • UniFi Access Point 7.0.47

    https://community.ui.com/releases/UniFi-Access-Point-7-0-47/e2da682c-0232-4a56-8b11-0aa3bb215f8a


    Overview

    UniFi Access Point 7.0.47 is only avaialble for Gen7 Access Points.

    Improvements

    • Improved device temperature management.

    Known issues

    • SSIDs using RADIUS assigned VLANs or on different VLANs from the native VLAN may operate at slower than expected speeds. This is our top priority to resolve.

    Additional information

    • Refer to the Help Center article here to determine the UniFi Access Point generation.
    • Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
    • If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

    If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

    • AP model(s)
    • Previous AP release version
    • UniFi Network application version

    Download links

    U7-Pro | md5sum | sha256sum

  • Ein Ostergeschenk für hoppel118 😉

    UniFi Access Point 7.0.49

    https://community.ui.com/releases/UniFi-Access-Point-7-0-49/8fe7fe75-37b9-494e-9d50-0fd1247c6565


    Overview

    UniFi Access Point 7.0.49 is only available for Gen7 Access Points.

    This update enhances VLAN client throughput for both static and RADIUS-assigned VLANs. We'd appreciate your feedback on VLAN throughput tests to see the impact on your setup. If you don't notice an improvement, please send us a support file and throughput results for a non-VLAN SSID on the same AP. Thanks for your patience!

    Improvements

    • Improved VLAN throughput.
    • Improved 2.4GHz latency and connection stability.
    • Improved interoperability with IoT devices.
    • Improved 6GHz range.
    • Improved WPA2/WPA3 roaming for WPA3 clients.
    • Reduced excessive logging.

    Bugfixes

    • Fixed SSIDs stop broadcasting after a few hours of uptime in rare cases.
    • Fixed repetitive logging (`append: not found`, `Scan table size`) in some cases.
    • Fixed false positive Rogue AP alerts when multiple APs are broadcasting at 6GHz.
    • Fixed manually set 6GHz channel occasionally changing automatically.
    • Fixed Auto channel not scanning for the cleanest channel when channel width is changed.
    • Fixed maximum supported bandwidth not being reported correctly for 320MHz capable clients.
    • Fixed kernel crashes to improve overall stability.

    Additional information

    • Refer to the Help Center article here to determine the UniFi Access Point generation.
    • Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
    • If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

    If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

    • AP model(s)
    • Previous AP release version
    • UniFi Network application version

    Download links

    U7-Pro | md5sum | sha256sum

  • Da bist du mir jetzt zuvor gekommen. Wollte hier auch gleich schreiben. Aber gut, dass du das so im Blick hast, was bei mir abgeht. 😂


    Anscheinend ist das Performanceproblem aber noch nicht bei allen gelöst.


    Ich habe jetzt mit meinen Geräten ca. 1500MBit up/down.


    Schöne Ostern!


    Gruß Hoppel

  • Welche Frequenz (5 oder 6 GHz) und welche Clients? Ich komme mit Wifi 6e mit 6Ghz nicht auf diese hohen Downloadraten, habe aber auch keine Wifi 7 Clients.

    Dann stimmt was mit deinem Setup nicht. Hier im ersten Beitrag siehst du dass ich mit dem U6-Enterprise ebenfalls schon diese Datenraten (1500MBit up/down) hatte. Nun auch mit dem U7-Pro.


    WiFi 7 Clients habe ich auch nicht. Meine Tests habe ich mit einem iPhone 15 Pro Max und einem iPad Pro 11“ 4. Gen. Die haben beide auch „nur“ WiFi 6e.


    Die Tests haben im 6 GHz Band auf einem 160MHz Kanal stattgefunden. Ich glaub, auf der 5GHz Frequenz unterstützen beide Geräte nur 80MHz Kanäle. Kann mich aber auch täuschen.


    Wie ist denn dein WiFi konfiguriert und welche Clients verwendest du zum Testen?


    EDIT: Diesem Beitrag nach wird bei 5 GHz auch bei den iPhone 15 Pro Modellen nur 80MHz unterstützt.

  • Ich habe ein Macbook M3 Pro, also WiFi6e. Mit der aktuellen Beta Firmware erreiche ich im Upload auch ca. 1600 MBit, Download max. 1200 Mbit. Habe zwei U7 Pro, ist bei beiden gleich.


    Ich habe ein eigenes WLAN für 6GHz auf Kanal 53 mit einer Kanalbandbreite von 160 MHz. Transmit Power High, BSS Transition ein. WPA3


    Mit dem Download kann ich leben, ich vermute das liegt an meinem Macbook, deshalb hat es mich interessiert welche Clients du hast...

  • Was ist deine iPerf3 Gegenstelle?


    Ich habe hier zwei Server:

    - Einen mit Dual Intel X550 10GBit Ethernet NIC

    - Einen mit Mellanox ConnectX-3


    Wenn ich einen Speedtest zur Intel mache, habe ich ähnliche Ergebnisse wie du, der Download ist 300-500MBit niedriger, als der Upload. Mit der Mellanox habe ich in beide Richtingen 1500-1600MBit.


    Denke nicht, dass es am Mac liegt.


    Gruß Hoppel

  • UniFi Access Point 7.0.53

    https://community.ui.com/releases/UniFi-Access-Point-7-0-53/738649ac-1253-4b5e-a9c1-b95394dbe721


    Bugfixes

    • Fixed IPv6 RAs leaking across VLANs.
    • Fixed APs going into an Adoption Failed state when the Network Application host (console) IP address changes.
    • Fixed RF Environment Scanning on APs not broadcasting any SSIDs causing the devices to get stuck in a `Scanning` state.
    • Fixed false-positive "Multiple devices are using the same IP address" alerts.
    • Fixed wireless adoption failure in rare cases.
    • Fixed rare client association failures when 3 or more 6GHz SSIDs are broadcasting on the same AP.
    • Fixed 6GHz channel being set to 1 after an RF Environment Scan.
    • Fixed false positive Authentication failures being reported on Radios->Connectivity page.
    • Fixed kernel crashes to improve overall stability.

    Additional information

    • Refer to the Help Center article here to determine the UniFi Access Point generation.
    • Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
    • If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

    If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

    • AP model(s)
    • Previous AP release version
    • UniFi Network application version

    Download links

    U7-Pro | md5sum | sha256sum

  • BlackSpy

    Hat den Titel des Themas von „Beta UniFi Access Point 7.x.x derzeit nur U7 Pro“ zu „Beta UniFi Access Point 7.x.x derzeit nur U7 Pro/ U6-Mesh-Pro“ geändert.
  • UniFi Access Point 7.0.55

    https://community.ui.com/releases/UniFi-Access-Point-7-0-55/8b68cafe-0119-4563-bef4-a42809db293b


    Improvements

    • Improved firmware update resiliency.
    • [Gen7] Improved thermal behavior.
    • [Gen7] Improved throughput and overall performance.
    • [Gen7] Improved DFS radar detection accuracy.

    Bugfixes

    • [Gen7] Fixed 6GHz connectivity regressions from 7.0.47.
    • [Gen7] Fixed kernel crashes to improve overall stability.
    • [Gen7] Fixed clients connecting at lower than expected rates after certain configuration changes.

    Additional information

    • Refer to the Help Center article here to determine the UniFi Access Point generation.
    • Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
    • If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

    If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

    • AP model(s)
    • Previous AP release version
    • UniFi Network application version

    Download links

    U6-Mesh-Pro | md5sum | sha256sum

    U7-Pro | md5sum | sha256sum