Final UniFi Access Point 6.x.x NUR GEN 6

Es gibt 6 Antworten in diesem Thema, welches 1.205 mal aufgerufen wurde. Der letzte Beitrag () ist von BlackSpy.

    UniFi Access Point 6.5.71

    https://community.ui.com/releases/UniFi-Access-Point-6-5-71/f14662df-ccb2-484e-91a7-2cd7be4b1057


    Overview

    UniFi Access Point 6.5.71 includes the improvement listed below and is only avaialble for Gen6 APs.

    Improvements

    • Added support for adopting UK-Ultra via Wireless Adoption.
    • Improved firmware update resiliency, especially when upgrading from 6.5.x to 6.6.x.

    Additional information

    • Refer to the Help Center article here to determine the UniFi Access Point generation.
    • Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Release Candidate.
    • If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

    If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

    • AP model(s)
    • Previous AP release version
    • UniFi Network application version

    Download links

    U6-Pro/Mesh/IW/Extender/Enterprise/Enterprise-IW | md5sum | sha256sum

    UniFi Access Point 6.6.65 nur Gen 6

    https://community.ui.com/releases/UniFi-Access-Point-6-6-65/3df9b0c0-7e51-4843-93a2-276c2d63e10a


    Overview

    UniFi Access Point 6.6.65 includes the improvements and bugfixes listed below. The changelog is compared to the latest official releases for Gen2/Gen3/Gen4/Gen5 APs and 6.6.65 for Gen6 APs.


    This release is now available on the Official release channel for the models/generations listed below, it's still a Release Candidate for all other models.

    • Gen6 Access Points

    Improvements

    • [Gen6] Improved reported client RSSI accuracy.

    Bugfixes

    • Fixed incorrect neighbor report BSSID Information in some cases.
    • Fixed APs going into "Adoption Failed" state in some cases when using a third-party gateway.
    • Fixed guest portal redirector not restarting gracefully after a crash (`Waiting previous redirector stop` in logs).
    • Reverted LED not flashing white and blue when AP firmware is updating. This was introduced in 6.6.60.
    • Fixed APs rarely going into an Adoption Failed state after a firmware update.
    • [Gen2/Gen3/Gen6] Fixed newly applied WiFi Speed Limit not taking effect until client reconnects.
    • [Gen2/Gen3/Gen6] Fixed channel width being reset to old configuration if it is configured right as an AP is booting when channel is set to Auto.
    • [Gen4/Gen5/Gen6] Fixed kernel crashes to improve stability.
    • [Gen2/Gen3] Fixed occasional false DFS radar hits in congested environments.
    • [Gen4/Gen5] Fixed client connection channel width being reported incorrectly as 20MHz after a client reassociates to the AP.
    • [Gen4/Gen5] Fixed 5GHz radio sometimes reporting a DFS CAC state after boot even if it is not configured to broadcast on a DFS channel.
    • [Gen4/Gen5] Fixed 2.4GHz broadcasting at 20MHz when configured for 40MHz.
    • [Gen4/Gen5] Fixed incorrect channel reported in Network application occasionally.
    • [Gen4/U6-Lite] Fixed 2.4GHz channel change causing new clients to not be able to connect to a WPA3 SSID.
    • [Gen4/U6-Lite] Fixed 2.4GHz connectivity issues with some IoT clients (e.g. Netatmo cameras).
    • [Gen6] Fixed 5GHz connections not working occasionally.
    • [Gen6] Prohibited the selection of 5GHz channels 165 and higher in UK when channel is set to Auto.
    • [Gen6] Fixed DFS channel configuration rarely not being applied.
    • [Gen6] Fixed Rx and Tx Rate displayed in the Network Application varying drastically.
    • [Gen6] Fixed APs configured to broadcast in Indonesia going offline after a firmware update with the AP LED flashing white constantly. This was introduced in 6.6.55.
    • [Gen6] Fixed 6GHz channel change causing a full provision (leading to all clients disconnecting) for ~60 seconds.
    • [Gen6] Fixed channel width changes occasionally not being applied.
    • [Gen6] Fixed TX Retries being reported incorrectly. This was introduced in 6.6.60.
    • [Gen6] Fixed maximum transmit power on DFS channels in the United States and Band-B channels in United Kingdom being set to lower than permitted limits when the AP is configured to broadcast at Auto / High transmit power.
    • [UAP-AC-IW] Fixed clients connected to other APs / switches incorrectly being listed as LAN clients connected to UAP-AC-IW.
    • [U6+] Fixed 5GHz radio continuing to broadcast on a non-DFS channel indefinitely after a radar hit.
    • [U6-LR] Fixed 5GHz radio occasionally getting stuck in a DFS CAC state even if the channel is set to Auto.

    Additional information

    • Refer to the Help Center article here to determine the UniFi Access Point generation.
    • Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Release Candidate.
    • If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

    If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

    • AP model(s)
    • Previous AP release version
    • UniFi Network application version

    Download links

    U6-Pro/Mesh/IW/Extender/Enterprise/Enterprise-IW | md5sum | sha256sum