Hm, neuer Kanal 🤔

UniFi Access Point 6.6.24

https://community.ui.com/releases/UniFi-Access-Point-6-6-24/1834fa5c-d232-44d9-9539-0174283b20e0

Improvements

• Eliminated client connectivity downtime when configuring SNMP, NTP, minimum rate, and toggling Debug Logging.
• Improved overall stability by fixing kernel crashes.
• [Gen4/Gen5] Improved RSSI calculation to increase minimum RSSI accuracy.
• [Gen6] Improved range by increasing maximum TX power in FCC countries.
• [U6+/U6LR+] Improved 2.4GHz latency.

Bugfixes

• Fixed band steering occasionally not steering dual-band clients from 2.4GHz to 5GHz after the 5GHz DFS CAC timeout.
• Fixed incorrect neighbor reports after an RF Scan.
• Fixed guest portal redirection not working when APs get a new IP on the guest VLAN (usually after 24 hours).
• [Gen2] Fixed high CPU usage when a lot of unauthorized guests are connected to a guest WLAN.
• [Gen2] Fixed 40MHz channel width not being applied correctly to 2.4GHz radio.
• [Gen4/Gen5] Fixed first client connection after boot failing occasionally.
• [Gen5] Fixed LED flashing white during firmware update in some cases.
• [UAP-Gen6] Fixed incorrect channels being used in outdoor mode.
• [U6-Lite/U6-LR] Fixed 5GHz channel occasionally not broadcasting after a channel change.
• [U6-Lite/U6-LR] Fixed low data rates being used for some 5GHz clients after switching to a DFS channel.
• [U6+/U6LR+] Fixed custom transmit power settings not being applied correctly.
• [U6+/U6LR+] Fixed 5GHz radio stuck in a DFS Waiting state if no 2.4GHz WiFi network is assigned to the AP.

Additional information

• Refer to the Help Center article here to determine the UniFi Access Point generation.
• Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
• If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

• AP model(s)
• Previous AP release version
• UniFi Network application version

Download links

UAP-AC-Lite/LR/Pro/M/M-PRO/IW | md5sum | sha256sum

UAP-HD/SHD/XG/BaseStationXG | md5sum | sha256sum

UAP-nanoHD/IW-HD/FlexHD/BeaconHD | md5sum | sha256sum

U6-Lite | md5sum | sha256sum

U6-LR | md5sum | sha256sum

U6+/U6-LR+ | md5sum | sha256sum

U6-Pro/Mesh/IW/Extender/Enterprise/Enterprise-IW | md5sum | sha256sum

UniFi Access Point 6.6.26

https://community.ui.com/releases/UniFi-Access-Point-6-6-26/5d36a950-27a6-411e-b271-e498265aaa4c

Improvements

• Added 6GHz support for Australia and Japan.
• [Gen6] Improved overall performance and latency.

Bugfixes

• Fixed kernel crashes to improve stability.
• [Gen5] Fixed APs rebooting when clients reconnect to a WPA3 WLAN after a reboot/firmware update. This was introduced in 6.6.24.
• [U6-LR] Fixed 2.4GHz radio randomly stops broadcasting. This was a race condition and occurs rarely.

Known issues

• [Gen6] Tx and Rx rates are not being reported correctly on this version. We will have a fix for this in the next release.

Additional information

• Refer to the Help Center article here to determine the UniFi Access Point generation.
• Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
• If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

• AP model(s)
• Previous AP release version
• UniFi Network application version

Download links

UAP-AC-Lite/LR/Pro/M/M-PRO/IW | md5sum | sha256sum

UAP-HD/SHD/XG/BaseStationXG | md5sum | sha256sum

UAP-nanoHD/IW-HD/FlexHD/BeaconHD | md5sum | sha256sum

U6-Lite | md5sum | sha256sum

U6-LR | md5sum | sha256sum

U6+/U6-LR+ | md5sum | sha256sum

U6-Pro/Mesh/IW/Extender/Enterprise/Enterprise-IW | md5sum | sha256sum

Hast du ne Enterprise für 6E? Denke eher nicht. Wifi 6 hat erstmal kein 6GHz, erst 6E und das kann nur der Enterprise

UniFi Access Point 6.6.27

https://community.ui.com/releases/UniFi-Access-Point-6-6-27/f9572eb0-e354-47cf-9c15-34e9db57bbae

Bugfixes

• Fixed kernel crashes to improve overall stability.
• [UAP-Gen4] Fixed intermittent 2.4GHz connectivity issues observed by some users (`MgmtRingFullCount` in log).
• [UAP-Gen6] Fixed AP state sometimes transitioning to 'Offline' in NET after a configuration change that forces a full provision, needing a power cycle to recover.
• [UAP-Gen6] Fixed Tx and Rx rates not being reported for connected clients. This was introduced in 6.6.26.
• [U6+/U6LR+] Fixed occasional client connectivity issues (`QDMA Tx hang` in log) introduced in 6.5.64.

Additional information

• Refer to the Help Center article here to determine the UniFi Access Point generation.
• Update your devices by changing the Device Firmware Release Channel in the UniFi Network application to Early Access.
• If you wish to go back to the Official release after the upgrade, change the release channel back to Official.

If you encounter any issues with this release, please provide us with some details on your setup and include the below information:

• AP model(s)
• Previous AP release version
• UniFi Network application version

Download links

UAP-AC-Lite/LR/Pro/M/M-PRO/IW | md5sum | sha256sum

UAP-HD/SHD/XG/BaseStationXG | md5sum | sha256sum

UAP-nanoHD/IW-HD/FlexHD/BeaconHD | md5sum | sha256sum

U6-Lite | md5sum | sha256sum

U6-LR | md5sum | sha256sum

U6+/U6-LR+ | md5sum | sha256sum

U6-Pro/Mesh/IW/Extender/Enterprise/Enterprise-IW | md5sum | sha256sum

Schneller als die Polizei erlaubt